How to Store RC LiPo Batteries Between Sessions

SUPULSE LiPo battery example; the nominal label voltage is not a storage setting

For a healthy, standard RC LiPo, about 3.8 V per cell is a storage reference, not a universal target. Use the storage target and procedure specified for your exact battery and compatible charger, then disconnect the pack and put it in a suitable storage location. The number is a reference, not a guarantee that a battery is safe.

What voltage should an RC LiPo be stored at?

The University of Pennsylvania's EHRS laboratory safety program gives approximately 3.8 V per cell as a storage reference. This laboratory guidance does not set the target for every RC battery. Follow the storage requirements for your exact pack and compatible charger.

Check the battery's chemistry, series cell count and storage instructions before selecting the charger profile. Do not apply an ordinary LiPo setting to LiHV, LiFe, NiMH or an unidentified pack. If the battery instructions and charger settings do not agree, resolve that mismatch before starting.

A compatible Storage program may add charge to a healthy pack after use or discharge a fuller pack. If your instructions refer to “half charge,” do not interpret that as half the voltage printed on the label or half the usual charging time.

Per-cell voltage and pack voltage

Per-cell voltage is the voltage of one cell; pack voltage is the total across the series-connected cells. The S count on an identified pack tells you how many cells are in series.

For a known pack, multiply the series cell count by the illustrative 3.80 V per cell below. These totals explain the arithmetic; they are not universal charger settings.

Known series count Illustrative pack total at 3.80 V per cell
1S 3.80 V
2S 7.60 V
3S 11.40 V
4S 15.20 V
5S 19.00 V
6S 22.80 V

For example, 3 × 3.80 V = 11.40 V for a known 3S pack. Do not use the table to identify an unlabeled battery. The nominal voltage printed on a battery label is not itself a storage instruction.

A matching pack total also cannot prove that the individual cells are balanced. Where your pack and compatible equipment support individual cell readings, check them as instructed. Follow the battery and charger guidance for a mismatch or warning rather than inventing an acceptable difference between cells.

Prepare a healthy pack after your session

Use this checklist only for a healthy pack, together with the instructions for your exact battery and charger.

  1. Disconnect the battery from the model. Remove it where the model and battery instructions require. Switching off the model is not a substitute for disconnecting the pack.
  2. Inspect before connecting a charger. Look for swelling, damaged wrapping, loose or exposed wires, leaks, unusual heat, odor or noises. USFA identifies changes in shape, excessive heat, leaking and odd noises as warning signs. Stop using an abnormal pack.
  3. Let normal post-run warmth settle. Do not charge a hot or wet battery. A healthy pack must meet its manufacturer's charging conditions before storage preparation begins. Excessive heat, swelling or hissing is a stop condition, not a routine cooldown. There is no single cooling time that this guide can safely assign to every pack.
  4. Check the exact charger setup. Confirm chemistry, cell count, voltage and the approved Storage procedure. Follow the connection arrangement for that pack and charger, including a balance lead where required. Do not assume every pack uses two separate connections.
  5. Stay present during the Storage cycle. Use the charging location and surface required by the equipment instructions, away from combustible materials. Never leave charging or discharging unattended.
  6. Finish and disconnect as instructed. Once the process is complete, disconnect the pack from the charger and protect its terminals from metal objects and other connectors. Penn EHRS warns against short circuits from conductive objects.

If plans change or your charger has no Storage mode

The outing was canceled after charging. Wind picks up or a broken part ends the day before you use the pack. If the healthy pack is now going into storage, use its approved Storage procedure rather than leaving it fully charged for the next uncertain outing. Do not guess a discharge time or improvise a load to reach a target.

The pack is low after a normal run. “Finished flying” does not mean “prepared for storage.” Inspect the pack, let ordinary warmth settle and follow the approved Storage procedure if it remains within the manufacturer's permitted operating conditions. If the charger reports low voltage or another fault, stop and check the instructions. Do not keep running the model toward zero or switch to another battery chemistry to force a charge.

Your charger has no Storage mode, or you cannot find one. First check the exact charger's manual rather than assuming the function exists. If it does not, gather the battery's brand/model, chemistry, cell count and connector information, plus the charger model. Ask the battery or model manufacturer for an approved storage method or compatible equipment. Do not estimate voltage by charging for a set number of minutes, disconnecting halfway through a charge, or improvising a discharge circuit. Use only the charger and settings specified for the battery; this article does not verify the Storage capability of any EXHOBBY-supplied charger.

Choose the location before the bag

Use a cool, dry location that stays within the battery manufacturer's storage conditions. USFA's battery guidance warns against direct sunlight, hot cars and nearby materials that can burn.

  • Keep packs away from heaters, direct sun, moisture and combustible materials.
  • Keep them out of reach of children and pets.
  • Keep terminals protected and separated from loose tools, screws and other connectors.
  • Choose the storage surface and enclosure according to the battery and enclosure instructions. Do not assume any metal box or improvised sealed container is suitable.

Follow the pack's specified storage conditions. Do not assume that a refrigerator or freezer is an approved storage location.

SUPULSE LiPo bag on an uncluttered tiled surface with a reminder that a bag is not a guarantee.
Illustrative scene: choose storage conditions for your exact battery and bag. A bag or tiled surface alone does not establish a suitable storage setup.

Optional storage bags from EXHOBBY

If your battery manufacturer permits storage in a LiPo bag, EXHOBBY has two options to compare:

SUPULSE two-pack LiPo storage bags SUPULSE LiPo storage bag with top handle and shoulder strap

Check usable internal space, room for the leads and complete closure against your battery's requirements. Listed outer dimensions alone do not establish fit. The reviewed product information does not establish a safe maximum battery-energy load or independently verified fire, smoke or explosion containment.

A bag is an additional precaution, not a guarantee against fire. It does not replace supervision during charging or discharging. A bag does not make a damaged pack safe to charge or suitable for routine storage with healthy batteries.

LiPo storage checklist

Long storage and the next session

For a seasonal break, follow the inspection schedule in the exact battery instructions. Do not apply another battery's schedule as a universal rule for every RC LiPo.

Keep a small record for each pack:

  • Pack identity: brand, model and your own identifier.
  • Preparation date: when the approved Storage process was completed.
  • Target and source: the battery instruction or compatible Storage profile used.
  • Readings and condition: individual cell readings where supported, plus any visible damage or warning.
  • Next check: the date required by the battery instructions.

This is a record template, not a prescribed inspection interval. If the instructions do not specify how to check a long-idle pack, ask the manufacturer before a long storage period. Storage is not a promise of a particular battery lifespan.

Before the next outing, inspect the wrap, shape, leads and connectors again. Check the voltage information required by the battery and charger instructions. If there is damage, an unexpected reading or a charger warning, stop rather than forcing a charge.

For a healthy pack that meets those checks, confirm the charger's chemistry, cell count and charge settings, then charge for the next session according to the battery instructions. Preparing a pack for storage is not the same as fully charging it for use.

When to stop storing and seek help

Stop using a swollen, leaking, damaged or unusually hot pack. Do not put it through a Storage cycle. USFA lists odor, color changes, excessive heat, changes in shape, leaking and odd noises as reasons to stop use. Do not try to repair the condition by charging, discharging or putting the battery in a bag.

For a cool, non-reacting damaged or retired battery: contact the manufacturer or an appropriate battery-collection facility for handling instructions. Tell the facility about the damage before taking the pack there. The EPA says lithium-ion batteries must not go in household trash or municipal recycling bins.

For active overheating, venting, smoke or fire: get people away from the area and seek emergency help. Do not pick up or carry a reacting pack. USFA advises evacuating and calling 911 for a lithium-ion battery fire, rather than trying to put it out yourself. Outside the United States, call the local emergency number.

After a session, inspect the pack and prepare it with the correct Storage procedure if it is healthy. Disconnect it, protect the terminals and record the next check. If the battery's condition is abnormal, stop the routine and get help.

Etiquetas:
Entrada antigua Volver a EXHOBBY RC BLOG Publicación más reciente